22
Sep, 2020
Garage Door Repair

Reset Garage Door Opener

If your garage door opener is malfunctioning, an unwanted remote is activating your garage door opener or your handheld opener has been lost or stolen, you’ll wish to reset the opener. the method for resetting your garage door opener varies counting on the brand, model, and age of your opener. Generally, garage door openers are simple to reprogram, however. Without manufacturer instructions available, a typical process could also be followed to rest most openers.


How Garage Door Openers Work
Older garage door openers believe DIP switches and radio frequencies to figure. Newer models typically use wireless technology instead. Garage door openers are often programmed in order that they open only one door approximately that multiple openers can open all doors. If a garage door opener’s frequency or wireless signal interferes with other household devices, you’ll find that you simply got to reset it.

To determine whether you’ve got an older or new model, check on the most unit for either a series of switchers or a button that says “Learn” or “Home.” If your garage door opener features a button, it’s likely newer. If it’s switching, you’ll get to reprogram it that way.

Resetting Older DIP Systems
The older garage door opened models typically work via a series of DIP switches. Many units have a series of 9 or 12 switches but numbers vary. These switches are located both on the most garage door opening unit and therefore the handheld remotes. Switches are often toggled in either an off or on position. so as for the garage door opener to function, the pattern of switches must match on both the in-garage motor and therefore the handheld remote. To access the switches, you’ll get to remove an impact panel or cover.

Resetting Newer Openers
Most newer garage door openers function by learning the frequency of the hand-held openers. To reset the system, you’ll get to locate the button on the motor that reads “Learn” or “Home.” In many cases, this button is going to be located on an equivalent side because of the device’s antenna and next to an LED. LED colors range by brand and model. counting on the model you’ve got, you’ll get to remove an access panel to succeed in this button.

Once you’ve got located the “Learn” or “Home” button, most models would require you to carry it down for five to 6 seconds or until the LED pops. for a few units, this is often all it takes to reprogram your opener.

In other instances, just after holding down the button until the LED pops, you’ll get to quickly press an equivalent button again to reset the opener.

you can contact Xpress Garage Door for Garage Door Services. we are also Offering free Coupons and 24*7 services.

Mail: xpressgaragedoors2010@gmail.com

Call: 224-400-9106

8
Sep, 2020
garage door

Steps to Remove a Garage Door

You must have a robust helper or two for a few of the steps.

Disconnect the Garage Door Opener
To remove an electrical garage door opener, first, close the garage door all the way, then unplug the motor unit from the wall socket. Pull the discharge cord hanging down from the opener track to disengage the opener’s trolley. Disconnect the trolley support arm from the door by removing the cotter and connecting bolt at the door end of the arm. The door is now separated from the opener, and you’ll remove the whole opener assembly, if desired, following the manufacturer’s instructions.

Remove the Garage Door Springs
Garage doors use springs to hold much of the load of the door during lifting and lowering. There are two sorts of spring mechanisms. Extension springs are located above the upper tracks on each side of the door. Torsion springs are attached to the header directly above the closed door. Torsion springs are always under tension and may be very dangerous to figure with if you do not know what you’re doing. If you’ve got torsion springs, call a garage door professional to possess the springs unwound safely.

To remove extension springs, open the garage door all the way and fasten C-clamps or pliers to the tracks on each side to stop the door from rolling down once the springs are removed. this is often important: Garage doors (even thin metal doors) are very heavy and may come down with great force without the springs carrying the majority of their weight.

Temporarily tape or tie each spring to a door track. Use pliers to get rid of the lift cable from the rock bottom bracket on all sides of the door. Disassemble the spring and pulley assemblies.

Lower the Door
Set blocks of wood on the ground where the door meets the ground. The blocks will prevent you from pinching your fingers once you lower the door. With one or two helpers supporting the load of the door within the open position, remove the clamps from the door tracks. Carefully lower the door until it rests on the woodblocks.

Warning
The door may weigh several hundred pounds. confirm you and your helpers can safely carry the load of the door while lowering it.

Remove the Door Panels
You will remove the door panels one at a time, performing from top to bottom. Start by removing the bolts securing the hinges to the highest door panel, employing a wrench. a typical 16-foot door has two roller hinges (one at each end of the panel) and three regular hinges in between. Remove the bolts only on the highest half each hinge, leaving rock bottom halves attached to the lower door panel.

With a helper or two supporting the highest of the highest panel, remove the roller bracket at each end of the panel. Carefully tilt the panel back and lift it far away from the tracks and therefore the remainder of the door. Set the panel aside.

Repeat an equivalent process to get rid of the remaining door panels. If desired, remove the door tracks by unbolting the sections one at a time. The vertical track sections are going to be fastened to the wall with lag bolts; remove these with a wrench.

you can contact us for more informaton and repair services.

we are also offering free coupons.

 xpressgaragedoors2010@gmail.com

224-400-9106

30
Jul, 2020
Residential and commercial garage door services

How can I replace a Garage Door Panel?

Let’s start with understanding that this is not a one-person job. I recommend that you get several estimates from professional repair companies before proceeding on your own. The steps to replacing a panel are simple but not easy.

  1. Remove items inside the garage (like cars and other garage contents) so that the door and its tracks can be accessed on the outer edges of the door. Obtain a couple of ladders to access the door springs.
  2. Release the spring tension on the door (this can be dangerous). Make sure that the springs are not broken. This would be the perfect time to replace them if damaged.
  3. Roll the panels ABOVE the one to be replaced higher in the tracks and secure them there. You will see where these upper panels must be separated from the panel to be replaced. Make sure these panels cannot move and fall out of the tracks.
  4. Remove the damaged panel from the tracks and take out the damaged panel. Check the tracks to ensure that they are in good condition. Repair/replace as needed. If the top panel must be replaced (where the opener attaches), you will need to install the opener connection on the new panel. If the bottom panel must be replaced (where the cables attach), you will need to install the cable connections on the bottom of that panel.
  5. Insert the new panel and rollers into the tracks, check for proper operation. Perform any re-installation described above.
  6. Disconnect the door opener trolley and manually lower the panels above to the top of the new panel. Reconnect all the panels vertically so that the opener will work. It’s only attached to the highest panel.
  7. CAREFULLY re-tension the spring tension. Most experts advise that cables and springs should not be touched by homeowners since these high-tension parts can be dangerous.
  8. Leaving the opener trolley disconnect open, manually open the door once spring tension is restored. The door should open easily by hand (e.g. if the electric power for the opener was lost) but should not “fly up” (oops, too tight).
  9. Reconnect the opener trolley so the opener can raise/lower the door and test for proper function.
  10. Discard the old door panel. You may have to cut it into pieces for disposal.

Contact us for more information.

6
Jun, 2020
types of garage doors

What are the types of Garage door?

There are a lot of choices when it comes to garage doors. To use this to your advantage, take the time and get to know what options are available to you. you’ll see garage doors that slide to the side or roll-up swing up, swing-out.

There are different quality type garage doors there are electric garage door, sensor garage door, manual doors, etc. Size, shape, and overall functionality. Different types of doors are used for different types of buildings and different types of floor plans.

Sectional Garage Doors

This type of garage door is made up of large no of horizontal panels drawn together by hinges. Installed with rollers usually rolling up, it then moves through two tracks parallel to each other to open. While sectional garage doors follow construction and mode of operation, they can come in a range of styles and designs to complement the rest of your home and complete your needs.

Swinging Carriage-House Garage Doors

they are Also called swing-style doors, these garage doors operate very much like French doors, supported by jambs on multiple hinges. They are often made of wood or composite material, imparting the same elegant vibe that wooden entry doors are well-known for.

Tilt-Up Garage Doors

Tilt-up doors function a pivoting hinge mechanism. This allows the door to slid upward and be lifted as a whole and into the ceiling of a garage to be kept out of the way. There are also variations in tilt-up doors you might want to take into consideration. These include retractable designs (which operates like a canopy door but fully retracts into the garage’s ceiling) and canopy styles (where a portion of the door, usually the bottom, goes beyond the garage).